ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ» º Adaptec, Incorporated AHA-1540B/42B º ÌÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ͹ º LED FLOPPY HARD DRIVE F1 º º ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ º º Floppy (34 pins) ³.... 1::::::: 1::::::::::::: Ú¿ ³ÉÍÍÍ º º INT.HD.(50 pins) ³ ÍÍ2ÍÍ ÍÍ3ÍÍô ÚÁ×Ä¿ º º EXT.HD.(50 pins) ³ ÍÍ5ÍÍ ÀÙ ³ º ³ º º ³ J5 1:::::::::::: 1: ³ º ³EXT. º º ÍÍ2ÍÍ SCSI BUS ³ J6 1:::: :: ³ º ³SCSI º º Term. Resistors ³ ÚÄÄÄÄÄ¿ ÚÄÄÄÄÄÄ¿ :: ³ º ³ º º ³ ³uCODE³ J8 1:::::: ³ BIOS ³ J7 ³ º ³ º º F1: 1.5A, 125V ³ ÀÄÄÄÄÄÙ J9 1:::::::: ÀÄÄÄÄÄÄÙ ÀÂ×ÄÙ º º Term. Power Fuse ÀÄÄÄÄÄÄÄÄÄÄÄ¿ Ú¿ ÚÄÄÙº º º ÀÄÄÄÄÄÄÄÙÀÄÄÄÄÄÄÄÄÄÄÄÄÙ º º º º º INTERFACE: ISA(AT)->SCSI-2 º º CONTROLS: 2 Floppy Drives (1542B only)(360KB, 720KB, 1.2MB, 1.44MB)º º 7 SCSI Devices º º º º J5: General Control º º J5-1: Synchronous Negotiation Enable: *Disabled: (no Jumper) º º Enabled: J5-1 Jumpered º º º º J5-2: Diagnostics (Factory use ONLY): *Disabled: (no jumper) º º º º J5-3: SCSI Parity Bit: *Enable Parity: (no jumper) º º Disable Parity: J5-3 Jumpered º º º º J5-4,5,6: SCSI Address: 0 1 2 3 4 5 6 7 (7 is Default) º º 4 x - x - x - x - º º 5 x x - - x x - - (x = Jumpered) º º 6 x x x x - - - - º º º º J5-7,8: DMA Channel: 0 5 6 7 (5 is Default) º º 7 x - x - º º 8 x x - - º º º º J5-9,10,11: Interrupt Chan.: 9 10 11 12 14 15 (11 is Default) º º 9 - x - x - x º º 10 - - x x - - º º 11 - - - - x x º º º º J5-12,13: DMA Transfer Speed: 5.0 5.7 6.7 8.0 (5.7 is º º 12 - x - x Default) º º 13 - - x x º º º º J6: BIOS/Auto Sense Control: 1 x 1: BIOS Enable º º 2 - 2,3,4: Not Used º º 3 - 5: Auto Sense disable º º 4 - º º 5 - (1 is Default) º º º º º ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ» º AHA-1540B,1542B Page 2 º ÌÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ͹ º º º J7: Address Selection º º º º J7-1: Floppy Secondary Address (Default is not jumpered) º º º º J7-2,3,4: AT I/O Port Addr.: 334 330 230 134 130 º º 2 - x - x - (Default º º 3 - - x x - is 330h) º º 4 - - - x x º º º º J7-5,6: BIOS Wait State (ns): 0 100 200 300 º º 5 - x - x (Default º º 6 - - x x is 0) º º º º J7-7,8: BIOS Address: DC000 CC000 D8000 C8000 º º 7 - x - x (Default º º 8 - - x x is DC000) º º º º J8: Floppy Disk Selection: 1: Floppy Enable (on Enabled ) º º 2,3: DMA REQ. (2 or 3) (2 DMA REQ.2) º º (1542B only) 4,5: DMA ACK. (2 or 3) (4 DMA ACK.2) º º 6,7: INT.REQ. (6 or 10) (6 INT.REQ.6) º º 8: Dual Speed Enable (off Disabled) º º º º J9: DMA/Interrupt: 1,2,3,4: DMA REQ. (0,5,6,7) (2 DMA REQ.5) º º 5,6,7,8: DMA ACK. (0,5,6,7) (6 DMA ACK.5) º º 9,10,11,12,13,14: INT.REQ. (9,10,11, º º 12,14,15) (11 INT.REQ.11) º º º ÌÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ͸ Additional Info ÕÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ͹ º º º This Host Adapter may also be ordered with a high-density SCSI-2 º º external connector, as part no: 1540B100 or 1542B100. º º º º SCSI bus terminators MUST be located at each end of the SCSI bus. º º If using internal SCSI peripherals only, the terminators on the H.A. º º must remain in place, and the device at the farthest point must also º º have it's terminators in place. All devices between must have their º º terminators removed. If using internal AND external peripherals, º º the devices at the end of the internal, and external cables should º º retain their terminators, and all those between, including the Host º º Adapter, should have theirs removed. º º º º Adaptec has added support for drives larger than 1GB with their º º 3.20 BIOS and uCODE. When correctly set up, the host adapter will º º automatically select the correct translation for the drive. The º º translation for drives over 1GB increases the heads. º º º º The 154x series is a Bus Mastering Host Adapter, and is well-suited º º for multi-tasking Operating Systems, such as UNIX and OS/2. º ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ