DIAMONTEL MESA 90X, 99X, 200 NOTES: These are dual NAM units. The ESN prefix is 134 decimal, 86 hex. See file MITSTEST.TXT for test mode access. NAM programing: 1. Press PWR key for one second to turn on phone. 2. Wait for wake up cycle to end and display to clear. 3. Within ten seconds press and hold the END key while entering 6 9 7 2 8 1 4 (reset code). 4. Release END. 5. The phone will display the first data entry. 6. Press the SEND key to store information and increment the step number. 7. Press CLR to correct any item. 8. Press END to complete programing and exit. PROGRAMING DATA: STEP# #OF DIGITS/RANGE DISPLAY DESCRIPTION 01 0 OR 1 DUAL NO 0=1 NAM, 1=2 NAMS 02 10 DIGITS NO1 NAM 1 MIN (AREA CODE AND TEL#) 03 00000 - 32767 SID1 NAM 1 SYSTEM ID 04 0 OR 1 LU NAM 1 LOCAL USE MARK 05 0 OR 1 E1 NAM 1 MIN MARK 06 333 OR 334 IPCH1 NAM 1 INITIAL PAGING CHANNEL 07 2 DIGITS AACCOLC1 NAM 1 ACCESS OVERLOAD 08 0 OR 1 PREF NAM 1 PREFERRED SYSTEM (SEE NOTES) 09 00 TO 15 GIM1 NAM 1 GROUP ID (10 FOR USA) 10 0 OR 1 RI1 NAM 1 ROAM INHIBIT 11 0 OR 1 DTX1 NAM 1 VOX OPERATION 12 0 OR 1 AR1 NAM 1 SYSTEM BUSY REDIAL If you selected 0 in step 01 go to step 24. 13 10 DIGITS NO2 NAM 2 MIN (AREA CODE & TEL#) 14 00000 - 32767 SID2 NAM 2 SYSTEM ID 15 0 OR 1 LU2 NAM 2 LOCAL USE MARK 16 0 OR 1 E2 NAM 2 MIN MARK 17 0333 OR 0334 IPCH2 NAM 2 INITIAL PAGING CHANNEL 18 00 TO 15 ACCOLC2 NAM 2 ACCESS OVERLOAD CLASS 19 0 OR 1 PREF2 NAM 2 PREFERRED SYSTEM (SEE NOTES) 20 00 TO 15 GI2 NAM 2 GROUP ID (10 IN USA) 21 0 OR 1 RI2 NAM 2 ROAM INHIBIT 22 0 OR 1 DTX2 NAM 2 VOX OPERATION 23 0 OR 1 AR2 NAM 2 SYSTEM BUSY REDIAL 24 4 DIGITS SEC SECURITY CODE 25 0 OR 1 EE DTMF SIGNALLING (SEE NOTES) 26 0 OR 1 C TONE CONTINUOUS DTMF 27 0 OR 1 AL AUTO LOCK 28 0 OR 1 BO HORN ALERT 29 0 OR 1 BEEP SERVICE ENTRY BEEP NOTES: Preferred system and end to end signalling are automatically set on the 99X model. To install lock code: With phone out of programing mode press FCN, 7, NNNN LLL CLR (where NNNN is 4 digit security code and LLL is new lock code). LOCK: F 2. UNLOCK: Enter three digit code. SYSTEM SELECT: F 1 displays current, then one of the following to change, CLR to exit: 0 = Pref/Non pref, 1 = Non pref/pref, 2 = Home only, 3 = Pref only, 4 = Non pref only.